Draper 89713 Plasterer's Feather Edge,1.2 m x 100 mm

Product Information

Many walls have lumps, bumps, depressions and hollows. These rarely show up until the first coat of paint goes on and then the reflection of the light casts all sorts of shadows making the paintwork look shoddy. Plasterers Trowels or floats come in a few sizes. Professional plasterers use longer, wider floats as they get paid by the amount they get on a wall in a day. The bigger the float, the more they get on! You will only need a standard float which is usually 11 inches by 4 inches wide. Specially designed High Quality Aluminium section. Finely tapered for maximum accuracy.Strong construction with thumb and finger groove down full length of section Please note, it does not very often make the chip invisible and some fine surface filler can be placed into the chip to be smoothed out with a paint scraper.

Feathering out with some filler will allow you to create a surface which will appear flatter even if it is not. By tapering the bumps and hollows out, the light will have no edges to reflect off and it will appear flat to the eye. Use tapered or feathered edge plasterboard for dry lining Materials Used for Feathering out Plaster, Filler or Dry Wall If you are attempting to feather out with filler, use some All-Purpose filler which can be pre or ready mixed. This will help you feather out well as the filler will be of the same consistency every time you use it. Clearly it originates with the properties of an actual feather where the density is reduced both from the centre to edge in a horzontal direction, as well as getting thinner and less dense from top to bottom. Feathering out a lump in a wall so that it is no longer noticeable Filling and Feathering out Different Levels and Coats of PaintMost often these bumps etc are not very big at all but it really makes a difference to the finished job. A slight bow in a Feather Edged Board can help it stay watertight Feather Edging Used in Preparing for Decoration Feathering Out Filler

Uk leading company in Plastering Tools, Screeding Tools, Levelling Tools and all related Construction Tools! Tough Tools have been successfully in operation for 20 Years serving the construction trade with high quality and trustworthy products. Our products are not mass imported and each item is manufactured in house in Yorkshire using only the highest quality materials.How flat and/or smooth should I be trying to get the wall with my trowel before using the feather edge to flatten. As a seasoned plasterer I naturally try to get it as flat as possible with the trowel. How flat am I trying to get it with the feather edge? Perfectly flat or just a bit better than a trowel finish? If the latter how much of a dip/bump can I leave in mm?

Use a fine sandpaper and rub the edges of the chipped edge hard so it slopes gently to the middle all round. This will give a flatter appearance.I battened off the large wall into smaller managable sections, followed the tips on here for preparing the substrate and getting the mix right and found it went on well (thanks everyone). I can get the wall looking pretty decent with just my trowel, but obviouly still need to remove the odd high spot and fill in the low spots. There are really wide blades used for feathering out wider gaps or bumps in walls and these are called caulking blades but for the novice it might be best to use a normal (but wide) scraper and even a plasterers float or trowel. The most obvious application for the DIYer or Home Improver, is in the Feather edged boards used for overlap fencing and panelling. By making sure the underside of the bow (the concave surface) faces the building, the bottom edge hugs the board beneath it really tightly when the board is fixed. This stops and water blowing up underneath the boards.

If you would like to know more about dry lining and errecting dry lined walls, see our project here. You can see a caulking blade being used with an ideal feathering out material called Fill and Skim in our video on YouTube. Feathers get less dense along their length Feather Edged Boards Used for Fencing and Garden BuildingsFeather out dry lining joints, filler or plaster with a taping knife or caulker Feathering out Dry Wall Plasterboard and Plasterboard Partitions When am I supposed to apply the feather edge? (how soft should the render be? completely fresh and wet? slightly firm to touch? etc)