Innokin T22 Pro Kit [Matte Black]

Product Information

The device is compatible with Prism T18E coils, however the kit comes with 2 new Pro coils both with a 1.7ohm resistance which perform best when vaping between 11-13.5W. Fill the tank as described above and for a new coil or first time use leave it to stand for 10 minutes for the coil to absorb the e-liquid.

The device arrives with the tank and mod separate so you need to screw the tank onto the mod, fill and charge and away you go! ThisInnokin Endura T22 Pro Vape Kit makes use of Prism T18 Pro coils in 1.7 ohm resistance (1 included in this kit) along with 1 x 1.5 ohm T18e coil, but are also compatible with the T18e/M18 range of coils. This range of coils are made for use with Mouth To Lung style vaping and delivery flavoursome vape when used with e liquids that have a maximum of 50% VG ratio such as 50/50, nicotine salt or high PG e liquids.

My device isn’t charging.

This despite looking like it is made from metal actually lights up in green, red or yellow depending on the battery charge remaining.

Breaking this down I got 15 hours vaping until the LED changed from Green to Orange (yes 15 hours!!!) The closer I looked at it, the more little details stood out, As you would expect with Innokin,the build quality and finish is superb.I often found myself admiring it during the photography.I.e. an old PC USB port only outputs around 0.5A whereas some of the modern charging plug adaptors and charging stations can output up to 2A. Open circuit – the LED will flash when the fire button is pressed – make sure tank and coil are correctly installed. First in our T22 Pro review is the design and build quality. The previous T22 from Innokin, while an incredible starter kit, was never going to win any awards for aesthetics. However, the T22 Pro has undergone something of a makeover to impress the eye as much as it eases your journey away from smoking. The Innokin Endura T22 Pro Kit is a relatively simple device to use. By following these steps, you should be able to get started vaping with it right away. Best Wholesale Vape Supplier – UPENDS

Filling the atomizer is simple. Just slide the top of the atomizer (top cap). The opening direction is indicated by engraved arrows. Impossible to go wrong! The opening to introduce the tip of the e-liquid bottle is quite small and only allows the finest tips. The holding and retention of the top cap are correct. The tank is protected by the metal body of the atomizer and unless you subject the atomizer to a huge fall, it is unlikely to see the glass break. It was a great coil when it came out and even still shone in newer kits, but the 1.6 and 1.7 ohm coils really have raced ahead in performance.Little details such as the On/Off slide switch, easy to see LED indicators and excellent build quality have made this mod feel more expensive than it actually is. windows surround the outside of the tank giving a clear view of the liquid level and it is that clear a view you can even see the coil resistance! Tank is a bit greedier on e-liquid than the pod kits I usually use – but this tank does have huge coils. Make sure to refill before it reaches only a quarter full or you could damage the coil.

Although the 1.5ohm is still a good coil – I think the kit should just focus on the other two coils and leave the 1.5ohm behind. UPENDS also offers a variety of other vaping products, such as e-liquids, coils, and accessories. If you are looking for a wholesale vape supplier that can provide you with everything you need to run a successful vaping business, then UPENDS is a great option. Conclusion: The Innokin Endura T22 Pro Vape Kit - A Top-Tier Choice Only use Lithium Ion rechargeable batteries in devices that have a built in protection circuit board(PCB) that detect shorts, over-discharge, over-charging etc. Use of lithium ion batteries without a PCB may increase your risk or explosion and,or fire.Adjusting the output wattage is also much easier with the 4 LED lights that feature below the fire button. These indicate what power setting is being vaped from a choice 9.5W, 11W, 12.5W and 13.5W. Tighten up your airflow. On the 1.2ohm coil especially, if the airflow is set closer to the "RDL" section, this will result in spotty auto-draw functionality.